The right number of solar panels depends on how much electricity your household uses, your roof space, and your future plans. This guide walks you through the calculation in three simple steps.
Get a Free System DesignIf you want a quick estimate, here's a guide based on typical Australian household sizes:
| Household | Typical Daily Usage | Recommended System | Number of Panels (400W) | Roof Space Needed |
|---|---|---|---|---|
| Single person or couple | 8–15 kWh | 5 kW | 12–13 panels | ~22 m² |
| Small family (2–3 people) | 15–25 kWh | 6.6 kW | 16–17 panels | ~30 m² |
| Average family (3–4 people) | 20–30 kWh | 6.6 kW – 10 kW | 17–25 panels | 30–45 m² |
| Large family (5+ people) | 30–45 kWh | 10 kW – 13 kW | 25–33 panels | 45–60 m² |
| Large home with pool/AC/EV | 40–60+ kWh | 13 kW+ | 33+ panels | 60+ m² |
Panel counts assume 400W panels. If using higher-wattage panels (e.g. 415W), you'll need slightly fewer.
Check your electricity bill for your average daily consumption in kilowatt-hours (kWh). Most Australian bills show this clearly. If yours shows quarterly totals, divide by 90 to get a daily average.
Typical daily usage by household:
Divide your daily usage by the average peak sun hours for your location:
System size (kW) = Daily usage (kWh) ÷ Peak sun hours
| City | Average Peak Sun Hours |
|---|---|
| Brisbane | 5.0 hours |
| Sydney | 4.6 hours |
| Canberra | 4.4 hours |
| Melbourne | 3.9 hours |
Example: A Sydney household using 25 kWh/day → 25 ÷ 4.6 = 5.4 kW system needed. You'd round up to a 6.6kW system to account for cloudy days and system losses.
Divide the system size by the wattage of the panels you're using:
Number of panels = System size (W) ÷ Panel wattage (W)
Example: 6,600W ÷ 400W = 16.5 → 17 panels
In Australia (Southern Hemisphere), the direction your roof faces significantly affects output:
| Roof Direction | Output vs North-Facing | Best For |
|---|---|---|
| North | 100% (maximum) | Best overall output — peak production around midday |
| East | ~85% | More morning generation — good for households active in the AM |
| West | ~85% | More afternoon generation — good for evening peak usage |
| East + West split | ~85% combined | Flatter generation curve — spreads output across more hours |
| South | ~60–65% | Generally not recommended in Australia |
If your panels face east or west instead of north, you may need 15–20% more panels to achieve the same total daily output.
The ideal tilt angle for solar panels in Australia is roughly equal to your latitude — about 25–35° for most of the east coast. Flat roofs require tilt frames. Steeper pitches may reduce winter output slightly.
Even partial shade on one panel can significantly reduce output from an entire string of panels. Trees, neighbouring buildings, aerials, and vent pipes can all cause shading. If shading is unavoidable, consider microinverters or DC optimisers, which allow each panel to operate independently.
If you're planning to add any of the following in the next few years, factor them into your system size now — extra panels are the cheapest component to add at installation time:
We almost always recommend installing a system 20–30% larger than your current calculated need. Here's why:
The average Australian home uses 18–25 kWh per day and is best served by a 6.6kW solar system, which requires 16–17 panels (at 400W each). The right number for your home depends on your specific usage, roof space, location, and future plans.
Find your daily electricity usage from your power bill (in kWh), divide by your location's average peak sun hours (e.g. 4.6 for Sydney, 5.0 for Brisbane), then divide the resulting kW figure by your chosen panel wattage (e.g. 0.4 kW for a 400W panel). This gives you the number of panels.
Each modern solar panel (400–415W) is approximately 1.8 m² in area. A 6.6kW system (17 panels) needs about 30 m² of suitable roof space. Panels can be split across multiple roof faces if needed.
Yes — oversizing is usually smart. Extra panels are the cheapest component, and the additional generation helps if you add a battery, EV charger, or heat pump later. Most installers recommend a system 20–30% larger than current usage.
In Australia, north-facing panels produce the most energy overall. East- and west-facing panels produce about 85% of north-facing output. An east-west split can work well for households with morning and evening usage peaks. South-facing panels produce significantly less and are generally not recommended.
Solar Harbour's CEC-accredited team will assess your roof, energy usage, and goals to recommend the perfect system size — with transparent pricing and no obligation.
Get a Free System DesignOr call us on 1300 252 090